Grand Prairie Pool Pros provides professional pool automation & controls in Grand Prairie, TX for residential and commercial properties across the DFW Metroplex. Pool automation puts the pump, heater, valves, lights and water features on a schedule and on your phone. In North Texas the feature that actually justifies the cost isn't the app, it's freeze protection: when the air drops below your set point the controller starts circulation on its own, at two in the morning, whether you remembered or not.
That matters because Grand Prairie takes a hard freeze every few winters and moving water is what keeps a pump housing and a run of PVC from splitting. The alternative is you, awake, in a coat, at midnight, hoping you got to the breaker in time. A controller costs less than one cracked pump plus the plumbing repair behind it.
The rest of it's convenience that quietly becomes habit. Set the spa to 102 while you're still at the office. Have the pool light come on at dusk and off at midnight without anyone thinking about it.
Run the pump on a long low-speed cycle overnight and a short high-speed burst for the cleaner. Turn the waterfall on for the evening and let it shut itself off.
Pentair, Hayward and Jandy all build systems that do this competently, and the right one is usually whichever brand your pump and heater already are, because same-brand equipment talks over its own bus instead of needing a relay for every function.
Chemical automation is the next step up, and it changes your water rather than your schedule. An ORP sensor reads the actual sanitizing power of the water continuously, a pH probe watches acid demand, and the controller doses only when the numbers move.
Instead of the usual cycle of green on Monday and over-shocked on Tuesday, the water sits in range all week. It also stops you buying chemicals you didn't need, which across a Texas summer isn't nothing.
The catch is that probes need calibrating a couple of times a year and eventually replacing. Anyone who sells it as fit-and-forget has never owned one.
Retrofits are most of what we do here. Older equipment pads accept automation fine with two conditions: the pump should be variable-speed, because scheduling a single-speed pump only saves you the walk to the pad, and the valves need physical room for actuators. Where a pad is a nest of 1980s plumbing, we usually rebuild the pad and add the controller in one visit rather than bolting new brains onto old chaos.
Now, when to skip it. If you have a single-speed pump, a gas heater you fire twice a year and one light, an old-fashioned mechanical time clock with a freeze sensor covers the genuinely important part for a small share of the cost.
Automation earns its keep on pools with a variable-speed pump, a spa, a heater, water features and more than one valve to move. If you only have two of those, buy the equipment first and the controller later.
It'll still be on the shelf when you're ready.
With 15+ years of experience, our licensed and insured team brings the right materials and equipment to every job — gunite and shotcrete shells, PebbleTec and polished quartz interiors, white marcite plaster, glass mosaic and porcelain waterline tile, travertine coping and decking, variable-speed pumps — and backs the work with a written workmanship warranty. We serve Grand Prairie and nearby communities including Arlington, Mansfield, Cedar Hill, Duncanville.
What We Handle
Everything our pool automation & controls in Grand Prairie covers
One crew, one point of contact, and the full range of pool automation & controls work in Grand Prairie, TX. If it is on this list we do it in house rather than handing it to a subcontractor:
- pool automation system installation
- Pentair, Hayward and Jandy control systems
- smartphone pool control app
- automated chemical dosing and ORP control
- pH and chlorine sensors with feeders
- automatic valve actuators
- scheduling pumps, heaters and lights
- spa heat-up from your phone
- pool automation retrofit on older equipment pads
- freeze protection controls for North Texas winters
Not sure which one describes your situation? Describe it in plain words and we will sort it out — or browse the rest of our Grand Prairie services.
Materials, equipment and how we do pool automation & controls
The difference between pool automation & controls that lasts and pool automation & controls that gets redone in three years is almost always preparation and materials, not the finish you see on day one. We work with gunite and shotcrete shells, PebbleTec and polished quartz interiors, white marcite plaster, glass mosaic and porcelain waterline tile, spec them to the job instead of to the invoice, and write the material grades into the free estimate so you know exactly what you are buying.
Every Grand Prairie job runs the same way: site walk and measurements, written scope and fixed price, protection of the surrounding area, then the work itself with a daily clean-up. 15+ years of pool work in the DFW Metroplex means we have already met whatever your property is going to throw at us — awkward access, older construction, an HOA with opinions.
Where we do pool automation & controls outside Grand Prairie
Grand Prairie Pool Pros covers Grand Prairie and the surrounding communities of the DFW Metroplex. Crews run out to the same nearby cities every week, so an out-of-town job does not mean an out-of-town price.
- Pool Automation & Controls in Arlington, TX — Tarrant County, population 394,000
- Pool Automation & Controls in Mansfield, TX — Tarrant County, population 72,600
- Pool Automation & Controls in Cedar Hill, TX — Dallas County, population 49,100
- Pool Automation & Controls in Duncanville, TX — Dallas County, population 40,700
- Pool Automation & Controls in DeSoto, TX — Dallas County, population 56,100
- Pool Automation & Controls in Lancaster, TX — Dallas County, population 41,300
Start on the Grand Prairie Pool Pros homepage for a free estimate, or call (844) 511-2320 and describe the job.
Why Grand Prairie Chooses Grand Prairie Pool Pros
- ✓Over 15 years remodeling, resurfacing and building pools across Grand Prairie and the DFW Metroplex
- ✓Specialists in bringing 1980s and 1990s pools up to date: new interiors, tile, coping, decking and equipment
- ✓Residential and commercial, from backyard gunite pools to hotel, apartment and HOA pools built to Texas code
- ✓Shells engineered for Blackland Prairie clay, and equipment specified for North Texas hard water and hard freezes
The standards behind pool automation & controls
Quality here is not a matter of opinion — it is written down. The pool automation & controls work we do in Grand Prairie follows published industry standards: Pool & Hot Tub Alliance publishes the ANSI/APSP construction and barrier standards, and American Red Cross water safety sets out the layered-protection guidance every pool owner should read. If a contractor cannot tell you which standard a detail comes from, that is worth asking about before you sign.
Every pool automation & controls project in Grand Prairie gets the same attention, whether it is a single room or a full commercial job. We show up on schedule, keep the site clean, and stand behind the work — the estimate is free and there is no pressure.
Ready to get started? Call (844) 511-2320 for a free pool automation & controls free estimate in Grand Prairie, or request a quote and we'll get right back to you.